Window ebb does more than just a decorative function. It simultaneously solves several problems:
If we neglect the installation of the low tide, moisture will collect on the windowsill, the processes of destruction of finishing materials will begin: plaster will fall off, window frames will become unusable. If the slopes are covered with PVC, mold and mildew will form under them.
This is the main answer to the question, what are the slopes on the windows, and why they should be installed without fail. That is why the installation of structures is performed not only for the decorative design of the opening, but also in order to prevent possible destruction of the finish and structures.
A window ebb is a board installed from the street side at the bottom or top of the window and balcony. Regardless of the type, the design consists of the same components:
The top shelf is the main element that you need to pay attention to when choosing a product. Its value is selected in such a way that there are no obstacles in the way of water drainage through special holes.
Window tide plays not only an aesthetic role, giving the window block a finished look, but also performs a number of other functions:
Ebb tides do not allow the walls to get wet from water For each specific window, the ebb tide must be made according to individual measurements so that it can fully fulfill the tasks assigned to it.
Before choosing an element, you should study the basic requirements and technical dimensions of the future product:
Fig. 1 Inter-balcony partition in new houses
In some modern projects of residential buildings (P44T, P3M and KOPE-M-Parus), a common balcony or loggia of two neighboring apartments during construction is not separated by concrete slabs of buildings, therefore developers insulate balconies additionally, using the most affordable and cheap materials. The most common option is to install chipboard, fiberboard, PVC, metal profile or slate sheets in a steel corner frame. It is clear that such a partition on the balcony from a neighbor does not provide sound and thermal insulation, reliable protection against the penetration of people and pets, and in the case of insulation of a balcony or loggia, it needs to be dismantled, altered or supplemented with a more protected wall.
This is an average version that has good thermal conductivity and low weight. The construction takes literally a few hours. The sheet material has an almost perfectly flat surface, which means that alignment of the finished partition is not required. Additional advantages of drywall are environmental friendliness and fire resistance.
When carrying out work from the inside of the premises, all elements of the balcony or loggia are protected from heat loss, special attention is paid to the external enclosing structures and walls adjacent to the street or technical premises. To protect the loggia room from heat loss, the following work blocks must be performed:
To protect the loggia room from heat loss, the following work blocks must be performed:
All types of work do not require special professional training, so anyone can insulate their balcony or loggia on their own.
The best option for the capital version of the partition. It is recommended to use foam blocks with a thickness of 75 mm - they will not create a strong load on the base plate, do not eat up precious space, do not overlap the glazed parts of the windows. It makes no sense to use blocks of greater thickness in order to improve thermal insulation - for these purposes it is better to use modern and lightweight materials before the final decorative finish.
Sequence of work:
The slab on the loggia is constantly exposed to sunlight, rain and wind, which gradually destroys it. Self-leveling floor on the balcony is one of the ways to protect this element. Also, the screed is made to level the surface and warm the room. The technology for performing the work is quite simple, so everyone can do it with their own hands.
Self-leveling floor is a coating made of flowable mixtures based on cement or gypsum with polyurethane or epoxy resin, which have the property of self-leveling under the influence of gravity. It can be used as a base for finishing flooring or as an independent decorative floor. It is poured with a thickness of no more than 5 mm.
Self-leveling floors can be divided into several types:
This is one of the safest ways to get a flat and solid surface. It is used if the required leveling height is 3-5 cm. The screed is less than 3 cm fragile and, with a high probability, will crack quickly. At the same time, a screed thicker than 5 cm will unnecessarily overload the balcony ceiling.
Plastic windows need to be adjusted to troubleshoot. To do this, you can call specialists, or you can do everything on your own, following the instructions.
A prerequisite for the effective performance of the functions of a plastic window is the correct adjustment. It maintains the density of the porch, the required tightness, smooth movement of the sash without distortions and touching the frame. The primary adjustment of plastic windows is carried out by installers during their installation. After that, they should work without defects or irregularities. However, over time, small backlashes appear, the flaps begin to sag a little. In the future, these deviations increase, which interferes with the normal operation of the structure.
To adjust plastic windows yourself, you need a fairly simple set, including:
The tools in this set are usually always available at home. An exception may be a hexagon, without which you cannot cope with work - this is the main regulating tool. If you do not know which key is needed to adjust plastic windows, and where you can find it, then contact any furniture fittings store. 4 mm hexagons are used in the assembly of any modern cabinet furniture, so finding such a key will not be a problem.
A screwdriver and screwdrivers will be needed to work with screw connections, with which the fittings are attached to the profile. Pliers are essential as an auxiliary tool.
It is recommended to additionally prepare silicone grease for the hardware. In addition, WD-40 or other similar aerosol lubricants can be used.
Over time, this problem may appear due to the drying out of the rubber seal. It is solved according to the same scheme as when transferring windows to winter / summer mode - by adjusting the eccentrics. Try to ensure an even tight fit of the sash - for this, the eccentrics must be tightened equally, but observe the measure: too much pressure helps the seal to dry out as quickly as possible and subsequently there will be nothing left but to replace it.
In some mechanisms, the sash is held down by plates. If the flap is tight, the pressure tab is extended. For a tighter fit, turn the hex to the left when positioning the hinges on the left, and on the right, to the right.
Adjustment may be required for any movable elements of plastic window fittings, which include:
DIY glass shelves are an exquisite and inexpensive home decoration. Transparent and light, they are able to visually relieve the interior, making it spacious and light. The material suits any design - from modern to classic.
In order for the structure to be functional and withstand several kilograms, the product should not be thin. Usually it is recommended to take glass of at least 8 mm for this purpose.
To add more strength to it, the material is hardened. Thus, glass prepared specially for the shelves can withstand several tens of kilograms.
We want to show you how to make a glass shelf with your own hands with lighting - you will see that it is not difficult at all. Those who want to realize their vision of home comfort are striving to improve the interior elements with their own hands - it is for such people that we have prepared a master class with step-by-step instructions.
First of all, it should be noted that working with glass should be very careful, thinking over every movement.
First you need to take a glass cutter. Before cutting the material, you need to practice a little in order to avoid mistakes at the right time.
Next, you need to decide on the dimensions of the future structure and create a markup. This can be easily done with a regular marker.
Then you may need a belt sander. It is necessary for edging.