Classic fireplace for a private house

In today's market, you can find a variety of types of fireplaces that are suitable for a particular interior, style, etc. Fireplace designs can vary greatly. However, the most popular are classic models, distinguished by style and functionality that have been proven over the years. Classic fireplaces are products for country houses. It is quite difficult to install them in ordinary city apartments. Fireplaces fit perfectly into the atmosphere of a suburban home, complement it, decorate the atmosphere.

How is the fireplace installed?

The classic style implies the presence of shallow fireplace inserts. A fireplace portal can be made from a wide variety of materials, including wood, stone, tiles, etc. Portals can be decorated with classic ornaments, which gives the composition a finished look. Classic models may include a closed firebox. In this case, an important role is played not only by the general appearance of the fireplace, its design and decoration, but also its accessories - in particular, the glass with which the firebox is equipped. This glass must be heat-resistant so that it can reliably protect the room from the spread of fire. By installing a fireplace in the room, you can easily cope with the problem of heating the rooms of the whole house.

To install a fireplace, you must first think over its foundation. To organize the foundation, you will need reinforcement with a cross section of 1-1.5 cm, sand, crushed stone, cement, as well as waterproofing and a metal sheet (required for formwork). Under the foundation, a pit is first made, which depends on how massive the building is, as well as what type of soil is available in the area. The depth of the pit can start from 0.5 m and end with 1 m. The bottom of the created pit is laid out with rubble 8-10 cm thick. / P>

The dug hole is reinforced at the edges with formwork. Then, reinforcement is installed over the entire thickness of the foundation, poured with layers of concrete. Each layer must first be compacted, and only then can a new one be poured. The very last layer is carefully leveled. A waterproofing material is laid on top of such a base, on which a basic row of fireplace masonry is then laid.

The walls of the house may well be made of combustible material, so the fireplace will need to be additionally protected from the spread of fire. This is done using fire insulation, which is used as foil or drywall. The fireplace itself is laid out of bricks. There are a lot of brick types, which allows you to create interesting design effects. Also, the fireplace can be tiled.

How is fireplace cladding done?

As soon as the structure of the fireplace dries up, you can start lining it. The first stage is the application of plaster to level the walls of the fireplace. After the walls are dry, you can apply markings to them and carry out the cladding. First, the corners of the fireplace are finished. Special corner tiles are purchased for them.

Tiling is done using special glue. All seams are subsequently sealed with a heat-resistant mixture. Arranging a fireplace is a difficult process that a beginner is unlikely to be able to handle. It is best to entrust the construction of a fireplace to professionals who will help you get a pleasant addition to create a warm, cozy atmosphere in your home.

Where to choose a place for a fireplace in the house?

When choosing a place for a fireplace, there are several important factors to consider:

  • The space should be prepared as much as possible in terms of fire safety. This applies to the floor covering, which must be made of refractory and fire resistant material; nearby furniture and items made of flammable materials.
  • The chimney for the fireplace must never touch the roof truss system.
  • The size of the portal should be in harmony in terms of volume with the rest of the area. So, for example, the base area should not be more than 10%, the depth of the furnace should not be more than one third of the height, the height of the furnace should not be more than 60% of its width.

Classic fireplace for a private house

The intercom system is successfully used to protect the entrances to apartment buildings, office premises, and private land plots. Electromagnetic locks help prevent intrusion on someone else's property by uninvited guests, distributors of advertising brochures. It is not easy to open the Metakom intercom without keys, as it belongs to the category of reliable means of protection that allow you to increase the security of your personal property.

Intercom Metacom

What models does this manufacturer produce

In total, Metakom produces intercoms of two types: with or without a display. The presence of the screen output command assumes a slightly different device device, its programming, which complicates the process of gaining access without a special key. A model with a one-piece body without such inserts is considered simpler and more accessible to a common user.

With display

The equipment operates smoothly under difficult climatic conditions in the temperature range from -45 to +75 degrees. The dense metal case does not allow moisture to pass through, which significantly extends the life of the lock, and also means protection against interruptions in operation associated with wetting of the electronics.

The option with a display is preferable, since the degree of protection of the house is increased, and also when reconfiguring, all commands are immediately visible. Also, the display serves as an excellent hint to the agreed visitor who uses this type of intercom for the first time.

No display

Design features of the device

The Metakom device is a multi-drop type intercom with built-in microprocessors. To open such doors, special keys are used that contain a chip with an opening code.

Modification of M10 products. -TM4R is distinguished by the absence of a control board, a powerful transistor, as well as the leads out contacts to the glue block, which allows you to use different methods of connecting the unit.

A cascade of elements with a transistor is used for direct control over the lock winding. This means that you do not have to install an additional board or carry out the procedure for demagnetizing the lock.